LINCOLN ELECTRIC CO -- AIRCO EASY ARC 6011C;AWS E6011  -- 3439-00-262-2637
<pre>=====================  Product Identification  =====================

Product ID:AIRCO EASY ARC 6011C;AWS E6011
MSDS Date:08/01/1988
FSC:3439
NIIN:00-262-2637
=== Responsible Party ===
Company Name:LINCOLN ELECTRIC CO
Address:22801 ST CLAIR AVE
City:CLEVELAND
State:OH
ZIP:44117-2524
Country:US
Info Phone Num:216-481-8100
Emergency Phone Num:216-481-8100
CAGE:36232
=== Contractor Identification ===
Company Name:THE LINCOLN ELECTRIC CO
Address:22801 ST CLAIR AVE
Box:City:EUCLID
State:OH
ZIP:44117-1199
Country:US
Phone:216-481-8100
CAGE:36232

=============  Composition/Information on Ingredients  =============

Ingred Name:CELLULOSE AND OTHER CARBONYDRATES
CAS:65996-61-4
Fraction by Wt: 5%
Other REC Limits:NONE RECOMMENDED

Ingred Name:SODIUM SILICATE
CAS:1344-09-8
Fraction by Wt: <5%
Other REC Limits:NONE RECOMMENDED

Ingred Name:TITANIUM DIOXIDE
CAS:13463-67-7
RTECS #:XR2275000
Fraction by Wt: <5%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST; 9394

Ingred Name:MAGNESIUM OXIDE
CAS:1309-48-4
RTECS #:OM3850000
Fraction by Wt: <5%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:15 MG/M3 PARTICULATE
ACGIH TLV:10 MG/M3;TDUST; 9394

Ingred Name:MANGANESE  (SARA III)
CAS:7439-96-5
RTECS #:OO9275000
Fraction by Wt: 1%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:C 5 MG/M3 DUST
ACGIH TLV:5 MG/M3 DUST 9394

Ingred Name:SILICA, CRYSTALLINE - QUARTZ
CAS:14808-60-7
RTECS #:VV7330000
Fraction by Wt: 0.5%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:SEE TABLE Z-3
ACGIH TLV:0.1 MG/M3 RDUST;9394

Ingred Name:CALCIUM CARBONATE (MARBLE) (LIMESTONE)
CAS:1317-65-3
RTECS #:EV9580000
Fraction by Wt: 0.5%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST; 9394

Ingred Name:IRON
CAS:65996-67-0
Fraction by Wt: <0.5%
Other REC Limits:NONE RECOMMENDED

Ingred Name:POTASSIUM CARBONATE
CAS:584-08-7
RTECS #:TS7750000
Fraction by Wt: <0.5%
Other REC Limits:NONE RECOMMENDED

Ingred Name:CORE WIRE,65% CONSISTING OF INGREDIENT 11
Other REC Limits:NONE RECOMMENDED

Ingred Name:IRON
CAS:7439-89-6
RTECS #:NO4565500
Fraction by Wt: 80%
Other REC Limits:NONE RECOMMENDED

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:UNCLASSIFIED WELDING FUMES=5MG/M3 PEL
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:NO
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:SHORT TERM EXPOSURE TO WELDING FUMES,
    GASES OR DUST MAY RESULT IN DISCOMFORT SUCH AS DIZZINESS, NAUSEA,
    FEVER, DRYNESS AND/OR IRRITATION OF NOSE, THROAT AND EYES. SKIN
    SENSITIVITY MAY ALSO BE NOTED. A CUTE EXPOSURE FROM SOME TOXIC
    GASES MAYCAUSE PULMONARY EDEMA, ASPHYXIATION AND EXCESSIVE EXPOSURE
    CAN BE FATAL.
Explanation of Carcinogenicity:THERE ARE NO INGREDIENTS ABOVE 0.1%
    WHICH ARE IDENTIFIED AS CARCINOGENS BY NTP,IARC OR OSHA.
Effects of Overexposure:EXPOSURE TO WELDING FUMES MAY RESULT IN
    DISCOMFORT SUCH AS DIZZINESS, NAUSEA, FEVER, DRYNESS AND/OR
    IRRITATION OF NOSE, THROAT AND EYES. SKIN SENSITIVITY MAY ALSO BE
    NOTED. WATERY EYES, HEADACHE, BREA THING DIFFICULTY, FREQUENT
    COUGHING AND/OR CHEST PAINS MAY OCCURE FROM ACUTE EXPOSURE. TOXIC
    GASES CAN BE FATAL.
Medical Cond Aggravated by Exposure:SOME WORKERS MAY BE AFFECTED BY A
    PRE-EXISTING CONDITION OR OTHER OCCUPATIONAL ILLNESS BECAUSE OF THE
    WIDE VARIATION IN INDIVIDUAL SUSCEPTIBILITIES.

=======================  First Aid Measures  =======================

First Aid:IN CASE OF ELECTRICAL SHOCK, TURN OFF POWER PRIOR TO REMOVAL
    FROM EXPOSURE AREA AND ADMINISTRATION OF FIRST AID. REMOVE FROM
    EXPOSURE AREA AND CALL FOR MEDICAL AID. ADMINISTER OXYGEN IF
    BREATHING IS D IFFICULT. IF NOT BREATHING, BEGIN ARTIFICIAL
    RESPIRATION. IF NO DETECTABLE PULSE, BEGIN EXTERNAL HEART MASSAGE.
    EMPLOY FIRST AID TECHNIQUES RECOMMENDED BY THE AMERICAN RED CROSS.

=====================  Fire Fighting Measures  =====================

Flash Point:NONE
Extinguishing Media:USE WATER FOG, CARBON DIOXIDE, FOAM, OR DRY
    CHEMICAL.
Fire Fighting Procedures:WEAR FIRE FIGHTING PROTECTIVE EQUIPMENT AND A
    FULL FACED SELF CONTAINED BREATHING APPARATUS. COOL FIRE EXPOSED
    CONTAINERS WITH WATER SPRAY.
Unusual Fire/Explosion Hazard:COMBUSTION OR HEAT OF FIRE MAY PRODUCE
    HAZARDOUS DECOMPOSITION PRODUCTS AND VAPORS.

==================  Accidental Release Measures  ==================

Spill Release Procedures:CLEAN UP ANY GRINDING DUST OR WASTE RESIDUES
    AND PLACE IN SUITABLE DOT APPROVED CONTAINERS AND DISPOSE OF IN
    FULL COMPLIANCE WITH FEDERAL, STATE AND LOCAL REGULATIONS. AVOID
    INHALATION AND SKIN EXPOSU RE.

======================	Handling and Storage  ======================

Handling and Storage Precautions:WEAR GLOVES AND FLAME RETARDANT
    CLOTHING WHEN CUTTING, GRINDING OR WELDING. DO NOT EXPOSE SKIN TO
    RADIATION WHEN HOT CUTTING OR WELDING.
Other Precautions:PROVIDE PROTECTIVE SCREENS TO SHIELD OTHERS. WHEN
    ELECTRODES AND FLUXES ARE CONSUMED, THE FUME AND GAS DECOMPOSITION
    PRODUCTS GENERATED ARE DIFFERENT IN FORM FROM THE INGREDIENTS
    LISTED. NEW COMPOUNDS  NOT IN THE ELECTRODES MAY FORM.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE WELD FUME RESPIRATOR OR AIR SUPPLIED
    RESPIRATOR WHEN CUTTING, GRINDING OR WELDING IN A CONFINED SPACE OR
    WHERE LOCAL EXHAUST OR GENERAL VENTILATION DOES NOT KEEP EXPOSURE
    BELOW RECOMMENDED LIMITS.  USE ONLY NIOSH APPROVED RESPIRATORS.
Ventilation:USE ENOUGH VENTILATION WHEN CUTTING, GRINDING OR WELDING TO
    KEEP THE DUST, FUMES & GASES FROM THE WORKERS BREATHING ZONE
Protective Gloves:WELDERS LEATHER GLOVES
Eye Protection:OSHA APPROVED GOGGLES/FACE SHIELD W/LENS
Other Protective Equipment:FLAME RETARDANT CLOTHING WHEN CUTTING,
    GRINDING OR WELDING. DO NOT EXPOSE SKIN TO RADIATION WHEN HOT
    CUTTING OR WELDING.
Work Hygienic Practices:WASH THOROUGHLY BEFORE EATING OR SMOKING.
    LAUNDER CONTAMINATIED CLOTHING BEFORE REUSE.
Supplemental Safety and Health
WELDING AND HOT CUTTING FUMES & GASES CANNOT BE CLASSIFIED SIMPLY.
    THEIR COMPOSITION AND QUANTITY ARE DEPENDENT ON THE METAL BEING
    WELDED, THE PROCEDURES, PROCESSES AND THE TYPE OF WIRE OR
    ELECTRODES	USED. OTHER INFLUENCING FACTORS ARE THEPRESENCE OF
    CONTAMINENTS. CHLORINATED SOLVENTS MAY DECOMPOSE TO TOXIC GASES.

==================  Physical/Chemical Properties  ==================

HCC:N1
Appearance and Odor:WELDING ROD;14" X 0.125"OD
Percent Volatiles by Volume:NIL

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AGENTS
Stability Condition to Avoid:HIGH HEAT, OPEN FLAMES AND OTHER SOURCES
    OF IGNITION
Hazardous Decomposition Products:WELDING AND CUTTING OPERATION MAY
    INCLUDE OXIDES OF THE METALS, CHROMATES, FLUORIDES, COMPLEX
    METALLICS, AND OZONE.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE I/A/W FEDERAL, STATE & LOCAL REGULATIONS

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.